Livraison gratuite sur l’ensemble de notre catalogue
Livraison en 14 jours ouvrés

1000W Panneau solaire Cellule solaire 500W panneaux solaires Chargeur de batterie solaire 400W 200W 100W batterie solaire flexible 16.5V Module photovoltaïque haute efficacité Kit Diy Génération voiture maison camping

Plage de prix : 190.17€ à 1,343.07€

- +
Paiements 100 % sécurisés
  • paypal pure
  • klarna
  • Livraison gratuite
    sur l’ensemble de notre catalogue.
  • Paiement en 3x Klarna :
    plus de flexibilité au moment de régler.
  • Retour gratuit sous 14 jours :
    pour votre tranquillité d’esprit.
  • Expédition soignée :
    colis protégé et suivi de commande.

Témoignage(s)

i

"Ce panneau solaire est vraiment impressionnant ! La qualité de fabrication est irréprochable et la performance est au rendez-vous. J'ai pu facilement l'installer et le mettre en service sans aucun souci. La seule petite chose à améliorer serait le poids un peu élevé, mais cela ne remet pas en cause la fiabilité du produit. Dans l'ensemble, je suis très satisfait de mon achat et je le recommande sans hésiter !"

Description

Espace réservé

The flexible solar panel made of Mono cell with conversion rate of 23%. The weight is 4lb, which is 30% of the traditional solar panels. Lightweight,portable nature of flexible solar panels makes more effective for RVs, caravan,boats,trailers,cabin,etc. , easy to install, plug and play.

16.5V 100W Flexible solar panel Specification

Maximum power(Pmax) 100 Watt

Maximum system voltage 700V DC

Open circuit voltage(Voc) 19.8V

Short circuit current(Isc) 6.66A

Maximum power voltage(Vmp) 16.5V

Maximum power current(Imp) 6.06A

Weight 1.8kg/4.0lb

Size 1140X460X2.5mm / 44.88X18.11X0.098 inch
Cable length 90cm/10FT
Operating Temperature -45℃ to 80℃ /-49℉ to 176℉

Operating temperature(NOCT) 45 plus or minus 2 Celsius system

STC: lrradiance1000w/m2,Temperature 25 Celsius system, AM=1.5

Please note: If you test the solar panel, the solar panel must be tested under the sun. The solar panel is exposed to sunlight at different times and the temperature is different, which will affect the output power of the solar panel.

1 Years Warranty, 8-10 Year Lifetime
Minor reduction in efficiency under partial load conditions at 25degC: at 100 W/m2, 95%- (+/-5%) of the STC efficiency (1000 W/m2) is achieved.

Extra: We keep right to change the specification of the data, and there is about ±5%deviation for all specification, pls notice this point.

[Highly efficient]The solar panel uses high efficiency 210MM monocrystalline solar cells with a conversion efficiency of 23%-24%. Built-in bypass diode to better protect the solar panel.
[Ultra-light and Flexible] A single solar panel weighs only 4.0 pounds and is only 0.098 inch thick. It can be easily picked up and carried. The solar panel be bent up to 260°. Ideal for mounting on RV ,roofs, campers, trailers, boats, cabins, tents, and other uneven surfaces.
[Highly Durable] The solar panels come with an IP67 waterproof rating .Withstand heavy snow loads of up to 5400 Pa and high wind loads of up to 2400 Pa,suitable for outdoor weather.
[Functional] Solar panels are connected to a 12V-48V system depending on the battery, perfect solution for power supply. which can effectively deal with the difficult problems caused by power shortage and power outage.

Package 1:100W solar panel

1 pcs 16.5V 100 Watt solar panel

Package 2:12V 100W Solar Kit

1. 1 pcs 16.5V 100 Watt solar panel

2. 10A 12v/24v charge controller

3. 1 set 3m Extension cable with PV connector

4. 1 set 3m cable with alligator clip (connect to battery)

Package 3:200W solar panel

2 pcs 16.5V 100 Watt solar panel

Package 4:300W solar panel

3 pcs 16.5V 100 Watt solar panel

Package 5:400W solar panel

4 pcs 16.5V 100 Watt solar panel

Package 6:500W solar panel

5 pcs 16.5V 100 Watt solar panel

Package 7:600W solar panel

6 pcs 16.5V 100 Watt solar panel

Package 8:800W solar panel

8 pcs 16.5V 100 Watt solar panel

Package 9:1000W solar panel

10 pcs 16.5V 100 Watt solar panel

Package 10: 200W Solar Kit

1. 2 pcs 16.5V 100 Watt solar panel

2. 20A 12v/24v charge controller

3. 1 set 3m Extension cable with PV connector

4. 1 set 3m cable with alligator clip (connect to battery)

5. 2 in 1 adaptors

Package 11: 300W Solar Kit

1. 3 pcs 16.5V 100 Watt solar panel

2. 30A 12v/24v charge controller

3. 1 set Extension cable with PV connector

4. 1 set cable with alligator clip (connect to battery)

5. 3 in 1 adaptors

PET Solar Panel Features:

[Multiple Compatibility] Perfect solar power kit for a variety of off-grid applications like shed, cabin, gate opener, etc where 12V battery is used, as well as to charge and maintain AGM, Flooded, GEL, Deep Cycle and Seal Lead Acid, etc batteries in the car, Rv, boat, marine, trailer, camper, pump, etc.
[Light weight] Made of high efficient solar cells,withstand extreme weather conditions like UV, anti-rusting, IP65 waterproof.
[Intelligent Charging] Optimized 3-stages charging algorithm allows to charge the battery more efficiently, and prevent the battery from overcharge, over-discharge, over-voltage, short circuit, etc, fully protect battery and extend the lifetime.
[Visual Monitor] Visual bright LED indicators help to monitor battery conditions and better understand the status of solar panel and load. Exclusively equipped three working modes for load, allowing to set up the load to work under dusk to dawn automatically plus working hours according to personal requirement, very practical and useful.

The solar panels can be directly connected to a portable battery with control function (note the voltage input required for the battery)

Off-grid solar panel system: solar panels need to be configured with a controller and batteries to be used together.

Safety Instructions:

1.Make sure your battery has enough voltage for the controller to recognize the battery type before first installation.

2.The battery cable should be as short as possible to minimize loss.

3.Please note that your controller is suitable for your battery type!

4.The charge regulator is only suitable for regulating solar modules. Never connect another charging source to the charge regulator.

System Connection:

1.Connect the battery to the charge regulator – plus and minus.it will show 1 ,if it detects 12V battery, 2 if it detects 24V battery.

2.Connect the photovoltaic module to the regulator – plus and minus.

3. Connect the consumer to the charge regulator – plus and minus.

By-pass Diodes are pre-installed in junction box and a pair of 2.5MM2 cables with connectors comes with the panel automatically.

PWM Solar Controller

3 Controller connection instructions
a Before connecting the solar panel, please connect the controller to the battery first. Connecting the solar panel without connecting the battery may cause the controller to burn out and fail to display.
b After the controller is connected to the storage battery, connect the above-mentioned series or parallel solar panels to the controller through the transfer cable.
c Finally, connect the required DC load to the load end of the controller. If the load does not work, press the third button of the controller.
d According to the controller manual, adjust the parameters you need.

4 Precautions for installation of solar system

a When connecting this solar system, first connect the controller to the battery, and then connect the solar panel. Do not reverse the connection order.
b Please install the controller in a well-ventilated area such as indoors or shadows to avoid exposure of components and prevent water from entering the controller.
c The total power of the solar panel and DC load cannot be greater than the rated power of the controller (voltage × current), otherwise there may be a risk of burning the controller.
d The inverter cannot be connected to the controller, but must be connected to the battery.
e After installation, check whether all line connections are tight to avoid the danger of heat accumulation due to virtual connection.
f The positive and negative poles of the solar panel in the same series connection cannot be short-circuited to prevent damage to the solar panel.
g The positive and negative poles of the controller and battery should be checked clearly. Do not connect the positive and negative poles in reverse.

1000W 500W 400W 200W 100W Flexible Solar Panel 16.5V High Efficiency Photovoltaic Module Diy kit Generation car home camping car home camping


The flexible solar panel made of Mono cell with conversion rate of 23%. The weight is 4lb, which is 30% of the traditional solar panels. Lightweight,portable nature of flexible solar panels makes more effective for RVs, caravan,boats,trailers,cabin,etc. , easy to install, plug and play.

16.5V 100W Flexible solar panel Specification

Maximum power(Pmax) 100 Watt

Maximum system voltage 700V DC

Open circuit voltage(Voc) 19.8V

Short circuit current(Isc) 6.66A

Maximum power voltage(Vmp) 16.5V

Maximum power current(Imp) 6.06A

Weight 1.8kg/4.0lb

Size 1140X460X2.5mm / 44.88X18.11X0.098 inch
Cable length 90cm/10FT
Operating Temperature -45℃ to 80℃ /-49℉ to 176℉

Operating temperature(NOCT) 45 plus or minus 2 Celsius system

STC: lrradiance1000w/m2,Temperature 25 Celsius system, AM=1.5

Please note: If you test the solar panel, the solar panel must be tested under the sun. The solar panel is exposed to sunlight at different times and the temperature is different, which will affect the output power of the solar panel.

1 Years Warranty, 10 Year Lifetime
Minor reduction in efficiency under partial load conditions at 25degC: at 100 W/m2, 95%- (+/-5%) of the STC efficiency (1000 W/m2) is achieved.

Extra: We keep right to change the specification of the data, and there is about ±5%deviation for all specification, pls notice this point.


[Highly efficient]The solar panel uses high efficiency 210MM monocrystalline solar cells with a conversion efficiency of 23%-24%. Built-in bypass diode to better protect the solar panel.
[Ultra-light and Flexible] A single solar panel weighs only 4.0 pounds and is only 0.098 inch thick. It can be easily picked up and carried. The solar panel be bent up to 260°. Ideal for mounting on RV ,roofs, campers, trailers, boats, cabins, tents, and other uneven surfaces.
[Highly Durable] The solar panels come with an IP67 waterproof rating .Withstand heavy snow loads of up to 5400 Pa and high wind loads of up to 2400 Pa,suitable for outdoor weather.
[Functional] Solar panels are connected to a 12V-48V system depending on the battery, perfect solution for power supply. which can effectively deal with the difficult problems caused by power shortage and power outage.





Package 1:100W solar panel

1 pcs 16.5V 100 Watt solar panel

Package 2:12V 100W Solar Kit

1. 1 pcs 16.5V 100 Watt solar panel

2. 10A 12v/24v charge controller

3. 1 set 3m Extension cable with PV connector

4. 1 set 3m cable with alligator clip (connect to battery)

Package 3:200W solar panel

2 pcs 16.5V 100 Watt solar panel

Package 4:300W solar panel

3 pcs 16.5V 100 Watt solar panel

Package 5:400W solar panel

4 pcs 16.5V 100 Watt solar panel

Package 6:500W solar panel

5 pcs 16.5V 100 Watt solar panel

Package 7:600W solar panel

6 pcs 16.5V 100 Watt solar panel

Package 8:800W solar panel

8 pcs 16.5V 100 Watt solar panel

Package 9:1000W solar panel

10 pcs 16.5V 100 Watt solar panel

Package 10: 200W Solar Kit

1. 2 pcs 16.5V 100 Watt solar panel

2. 20A 12v/24v charge controller

3. 1 set 3m Extension cable with PV connector

4. 1 set 3m cable with alligator clip (connect to battery)

5. 2 in 1 adaptors

Package 11: 300W Solar Kit

1. 3 pcs 16.5V 100 Watt solar panel

2. 30A 12v/24v charge controller

3. 1 set Extension cable with PV connector

4. 1 set cable with alligator clip (connect to battery)

5. 3 in 1 adaptors

PET Solar Panel Features:

[Multiple Compatibility] Perfect solar power kit for a variety of off-grid applications like shed, cabin, gate opener, etc where 12V battery is used, as well as to charge and maintain AGM, Flooded, GEL, Deep Cycle and Seal Lead Acid, etc batteries in the car, Rv, boat, marine, trailer, camper, pump, etc.
[Light weight] Made of high efficient solar cells,withstand extreme weather conditions like UV, anti-rusting, IP65 waterproof.
[Intelligent Charging] Optimized 3-stages charging algorithm allows to charge the battery more efficiently, and prevent the battery from overcharge, over-discharge, over-voltage, short circuit, etc, fully protect battery and extend the lifetime.
[Visual Monitor] Visual bright LED indicators help to monitor battery conditions and better understand the status of solar panel and load. Exclusively equipped three working modes for load, allowing to set up the load to work under dusk to dawn automatically plus working hours according to personal requirement, very practical and useful.

The solar panels can be directly connected to a portable battery with control function (note the voltage input required for the battery)

Off-grid solar panel system: solar panels need to be configured with a controller and batteries to be used together.

Safety Instructions:

1.Make sure your battery has enough voltage for the controller to recognize the battery type before first installation.

2.The battery cable should be as short as possible to minimize loss.

3.Please note that your controller is suitable for your battery type!

4.The charge regulator is only suitable for regulating solar modules. Never connect another charging source to the charge regulator.

System Connection:

1.Connect the battery to the charge regulator – plus and minus.it will show 1 ,if it detects 12V battery, 2 if it detects 24V battery.

2.Connect the photovoltaic module to the regulator – plus and minus.

3. Connect the consumer to the charge regulator – plus and minus.

By-pass Diodes are pre-installed in junction box and a pair of 2.5MM2 cables with connectors comes with the panel automatically.

PWM Solar Controller

3 Controller connection instructions
a Before connecting the solar panel, please connect the controller to the battery first. Connecting the solar panel without connecting the battery may cause the controller to burn out and fail to display.
b After the controller is connected to the storage battery, connect the above-mentioned series or parallel solar panels to the controller through the transfer cable.
c Finally, connect the required DC load to the load end of the controller. If the load does not work, press the third button of the controller.
d According to the controller manual, adjust the parameters you need.

4 Precautions for installation of solar system

a When connecting this solar system, first connect the controller to the battery, and then connect the solar panel. Do not reverse the connection order.
b Please install the controller in a well-ventilated area such as indoors or shadows to avoid exposure of components and prevent water from entering the controller.
c The total power of the solar panel and DC load cannot be greater than the rated power of the controller (voltage × current), otherwise there may be a risk of burning the controller.
d The inverter cannot be connected to the controller, but must be connected to the battery.
e After installation, check whether all line connections are tight to avoid the danger of heat accumulation due to virtual connection.
f The positive and negative poles of the solar panel in the same series connection cannot be short-circuited to prevent damage to the solar panel.
g The positive and negative poles of the controller and battery should be checked clearly. Do not connect the positive and negative poles in reverse.



🔧 Caractéristiques techniques:

  • Nom de marque: BOGUANG
  • Origine: CN (Origine)
  • Nombre de panneaux: 1
  • Panneau solaire flexible: Oui
  • Panneau Solaire Pliable: Non
  • Produit chimique à haute préoccupation: Aucun
  • Type: panneau solaire
  • Module Efficien: 24%
  • Numéro de Modèle: solar panel
  • Maximale. Puissance: 1000W
  • Taille: 1140*460*2.5mm
  • Matériau: Silicium monocristallin
  • Capacité nominale: 100W – 1000W
  • Nombre de cellules: 30 pcs solar cell
  • Personnalisé: Oui
  • Panneau solaire rigide: Non
  • Certification: CE
  • Certification: FCC
  • Certification: ROHS
  • Certification: weee
  • placa solar: zonnepaneel
  • solar charger: solarpanel
  • batterie solaire: pannelli solari
  • pannello solare: painel solar
  • paneles solares: flexible solar panel
  • placas solares: panel solar
  • panel fotowoltaiczny: panneau solaire
  • 100W Solar Panel: 1pcs 16.5V 100W Solar Panel
  • 200W Solar Panel: 2pcs 16.5V 100W Solar Panel
  • 300W Solar Panel: 3pcs 16.5V 100W Solar Panel
  • 400W Solar Panel: 4pcs 16.5V 100W Solar Panel
  • 600W Solar Panel: 6pcs 16.5V 100W Solar Panel
  • 800W Solar Panel: 8pcs 16.5V 100W Solar Panel
  • 1000W Solar Panel: 10pcs 16.5V 100W Solar Panel
  • 500W Solar Panel: 5pcs 16.5V 100W Solar Panel

📦 Informations de livraison:

  • Poids: 3.000 kg
  • Dimensions: 109x50x4 cm

⏱️ Délai de livraison estimé: 2 jours

Informations complémentaires

Couleur

Argent / gris, Autre, Black, Camouflage désert, Doré, Fauve, Lavande, Neige Camouflage, Numérique Camouflage, Vert Camouflage, bleu foncé, 透明色

Expédié De

CHINA, Canada, Espagne, France, Fédération de russie, République tchèque, États-unis

Avantages / Inconvénients

Avantages

  • Haut taux de conversion d'énergie solaire à 23%
  • Poids léger à seulement 4 lb, soit 30% du poids des panneaux solaires traditionnels
  • Conception flexible et portable, idéale pour les véhicules récréatifs, les caravanes, les bateaux, etc.

Inconvénients

  • Tension d'entrée maximale de 700V DC, limitant son utilisation dans certaines applications
  • Nécessité d'un espace d'installation adapté pour profiter de la flexibilité du panneau

Avis (0)

Avis

Il n’y a pas encore d’avis.

Soyez le premier à laisser votre avis sur “1000W Panneau solaire Cellule solaire 500W panneaux solaires Chargeur de batterie solaire 400W 200W 100W batterie solaire flexible 16.5V Module photovoltaïque haute efficacité Kit Diy Génération voiture maison camping”

Votre adresse e-mail ne sera pas publiée. Les champs obligatoires sont indiqués avec *

Comparaison de Produits Similaires

1000W Panneau solaire Cellule solaire 500W panneaux solaires Chargeur de batterie solaire 400W 200W 100W batterie solaire flexible 16.5V Module photovoltaïque haute efficacité Kit Diy Génération voiture maison camping

1000W Panneau solaire Cellule solaire 500W panneaux solaires Chargeur de batterie solaire 400W 200W 100W batterie solaire flexible 16.5V Module photovoltaïque haute efficacité Kit Diy Génération voiture maison camping

SOPEWOD support de rangement multifonctionnel magnétique support à épices mural à trois niveaux avec supports et supports de rangement de cuisine en métal

SOPEWOD support de rangement multifonctionnel magnétique support à épices mural à trois niveaux avec supports et supports de rangement de cuisine en métal

pliable pour bébé 090B, pour bain en toute sécurité, rangement facile, Portable pour bébé, en PVC,

pliable pour bébé 090B, pour bain en toute sécurité, rangement facile, Portable pour bébé, en PVC,

Bancs de douche HDPS, chaise de douche Durable, espaces de rangement à 2 niveaux et double poignées, tabouret étanche avec coussinets antidérapants pour le rasage

Bancs de douche HDPS, chaise de douche Durable, espaces de rangement à 2 niveaux et double poignées, tabouret étanche avec coussinets antidérapants pour le rasage

Prix Plage de prix : 190.17€ à 1,343.07€ 677.97 56.67 143.37
Disponibilité ✓ EN STOCK ✓ EN STOCK ✓ EN STOCK ✓ EN STOCK
Avantages
  • Haut taux de conversion d'énergie solaire à 23%
  • Poids léger à seulement 4 lb, soit 30% du poids des panneaux solaires traditionnels
  • Conception flexible et portable, idéale pour les véhicules récréatifs, les caravanes, les bateaux, etc.
  • Matériel robuste en acier au carbone et peinture durable
  • Design multifonctionnel pour ranger divers objets
  • Possibilité de personnalisation du logo
  • Rangement facile grâce à la conception pliable
  • Utilisation de matériaux PVC sûrs et inoffensifs pour la santé du bébé
  • Stabilité améliorée avec le design à renfort triangulaire
  • Matériau HDPS durable et résistant à l'eau, aux rayures et aux taches
  • Esthétique bois naturel attrayante
  • Conception avec espaces de rangement pratiques à 2 niveaux
Inconvénients
  • Tension d'entrée maximale de 700V DC, limitant son utilisation dans certaines applications
  • Nécessité d'un espace d'installation adapté pour profiter de la flexibilité du panneau
  • Garantie limitée à 6 mois seulement
  • Frais d'expédition variables selon les besoins du client
  • Peut être moins durable qu'une baignoire traditionnelle en plastique rigide
  • Risque de glissade plus élevé que dans une baignoire classique
  • Assemblage requis pour l'installation
  • Poids relativement élevé pouvant compliquer le transport
Action Voir le produit Voir le produit Voir le produit Voir le produit
Paiement sécurisé

Transactions protégées et méthodes de paiement sécurisées pour acheter vos robinets en toute confiance.

🚚
Livraison gratuite & suivie

Expédition soignée de votre robinetterie et suivi de colis pour savoir exactement où en est votre commande.

💬
Service client réactif

Une question sur un modèle ou une installation ? Notre équipe vous répond et vous oriente vers le bon robinet.

Panier
📐

Guide des Dimensions

📏 Dimensions & Compatibilités

Nombre de trous

Vérifiez le nombre de trous de votre évier ou lavabo avant de commander.

  • 1 trou : Mitigeur classique (le plus courant)
  • 2 trous : Bec séparé de la commande
  • 3 trous : Mélangeur chaud/froid séparés
💡 Regardez sous votre évier ou lavabo pour vérifier le nombre de trous.

Diamètres standards

  • Mitigeur lavabo : Ø 35 mm (tolérance 32-38 mm)
  • Robinet cuisine : Ø 35 mm (tolérance 32-40 mm)
  • Mélangeur 3 trous : Ø 25-28 mm par trou

Hauteur selon type de vasque

  • Vasque à poser : Hauteur minimum 15-20 cm
  • Vasque encastrée : Hauteur 10-15 cm
  • Évier cuisine : Hauteur 30-40 cm recommandée
⚠️ Un bec trop bas rend l'utilisation difficile. Un bec trop haut provoque des éclaboussures.

Portée du bec (projection)

  • Lavabo : 10-15 cm
  • Évier 1 bac : 15-20 cm
  • Évier 2 bacs : 20-25 cm + rotation 360°

🔧 Raccords & Filetages

Standards français

  • Flexibles robinet : 3/8" (~16,7 mm)
  • Arrivée d'eau murale : 1/2" (~20,9 mm)
  • Colonne de douche : 1/2" (~20,9 mm)
  • Baignoire : 3/4" (~26,4 mm)

Longueur des flexibles

  • Standard inclus : 30-40 cm
  • Meuble haut : 50-60 cm nécessaires
  • Installation éloignée : 60-80 cm
💡 Mesurez la distance AVANT de commander pour éviter les rallonges.

Mâle vs Femelle

  • MÂLE : Le filetage est à l'extérieur (vis)
  • FEMELLE : Le filetage est à l'intérieur (écrou)

Étanchéité

  • Joint plat : Pour les flexibles - PAS de téflon
  • Téflon : Raccords métal/métal - 5 à 8 tours
  • Filasse : Gros diamètres (3/4" et plus)

🚿 Compatibilité Vasque / Évier

🏺 Vasque à poser

Choisissez un robinet haut (25-35 cm) pour que le bec passe au-dessus de la vasque. Portée recommandée : 12-18 cm.

🪣 Vasque encastrée

Un robinet standard (15-25 cm) convient parfaitement. Hauteur sous bec : 10-15 cm. Installation 1 trou classique.

🍳 Évier 1 bac

Optez pour un mitigeur à bec orientable. Hauteur : 30-40 cm. Bec pivotant 120° minimum.

🍳🍳 Évier 2 bacs

Privilégiez un mitigeur haut avec rotation 360°. Portée : 20-25 cm pour couvrir les deux bacs.

🚿 Douche murale

Entraxe standard : 150 mm (norme française et européenne). Les raccords excentrés permettent un ajustement de ±10 mm.

💧 Pression & Chauffe-eau

Types de pression

  • Haute pression : 1 à 5 bars (standard en France)
  • Basse pression : 0,2 à 0,5 bar (rare)
⚠️ Tous nos robinets sont conçus pour la haute pression (installation standard).

Compatibilité chauffe-eau

  • Ballon électrique : Compatible
  • Chaudière gaz : Compatible
  • Instantané récent : Compatible si pressurisé
  • ⚠️ Instantané ancien : Contactez-nous avant commande

Si votre pression est faible

  • Nettoyez le mousseur (calcaire)
  • Vérifiez que les flexibles ne sont pas pliés
  • Installez un surpresseur si nécessaire
  • Choisissez un pommeau "haute pression"

✨ Finitions & Entretien

Comparatif des finitions

  • Chromé : Entretien facile, mais traces d'eau visibles
  • Inox brossé : Très facile d'entretien, peu de traces (recommandé)
  • Noir mat : Élégant, mais le calcaire est visible
  • Doré : Luxueux, entretien plus délicat

✅ À faire

  • Essuyer après chaque utilisation
  • Utiliser un chiffon microfibre
  • Nettoyer au savon doux
  • Vinaigre blanc dilué (occasionnellement)

❌ À éviter

  • Javel et produits chlorés
  • Éponges abrasives
  • Vinaigre pur (trop acide)
💡 Notre recommandation : inox brossé ou nickel brossé pour un entretien minimal.

🛠️ Installation

Outils nécessaires

  • Clé à molette (10-13 mm)
  • Clé de serrage pour robinet
  • Tournevis plat
  • Bassine + serpillière

Étapes d'installation

  1. Couper l'eau – Fermez les vannes d'arrêt ou le robinet général
  2. Purger – Ouvrez l'ancien robinet pour vider la pression
  3. Démonter – Débranchez les flexibles et l'écrou de fixation
  4. Installer – Placez le nouveau robinet avec son joint
  5. Raccorder – Chaud à gauche, froid à droite
  6. Tester – Ouvrez l'eau et vérifiez l'absence de fuites

⚠️ Erreurs à éviter

  • Trop serrer les flexibles (endommage les joints)
  • Oublier le joint d'étanchéité
  • Inverser chaud et froid
  • Plier les flexibles
👷 Faites appel à un plombier si : pas de vannes d'arrêt, tuyaux anciens ou corrodés, ou si vous avez un doute.

🛡️ Normes & Garanties

Garantie Aquaflux

  • Garantie : 2 ans minimum sur tous nos produits
  • SAV : Réponse sous 48h ouvrées
  • Contact : contact@aquaflux.fr

Matériaux de qualité

  • Corps : Laiton ou Zamak
  • Cartouche : Céramique (500 000 cycles)
  • Flexibles : Inox tressé + EPDM

Conformité

  • Sans plomb (normes européennes)
  • Cartouche céramique haute durabilité
  • Résiste jusqu'à 10 bars de pression
📩 Une question ? contact@aquaflux.fr
🕐 Lun-Ven 10h-12h / 14h-17h